Commercial Door Hinge Size Chart: 4-1/2 x 4-1/2 vs 5 x 4-1/2, Weight and Quantity
Posted by National Lock Supply on Oct 1st 2026
Quick Verdict
The standard commercial door hinge size is 4-1/2 x 4-1/2 in. on a 1-3/4 in. door up to 36 in. wide. Step up to 5 x 4-1/2 in. when the door runs over 36 in. wide or gets heavy, and to heavy weight (0.180 in. leaf gauge instead of 0.134 in.) when the door passes about 150 lbs, sees 400 cycles a day or more, or carries a closer on a high-traffic opening. Count is driven by height: three hinges on a door over 60 in. and up to 90 in. tall, four on doors over 90 in. up to 120 in. The first number in the part is height, the second is open width: a 4-1/2 x 4 is not a drop-in for a 4-1/2 x 4-1/2. These are common industry guidance; the door and frame manufacturer's template governs.
What hinge height fits my door thickness and width?
Height follows door thickness first, then door width. A thicker, wider leaf puts more leverage on the top hinge, so the hinge grows in height and, past a point, in leaf gauge. The table below reflects the rule of thumb most hardware schedules use; it is guidance, not a code requirement.
| Door thickness | Door width | Hinge height | Typical weight |
|---|---|---|---|
| 1-3/8 in. | Up to 32 in. | 3-1/2 in. | Standard |
| 1-3/8 in. | Over 32 in. to 37 in. | 4 in. | Standard |
| 1-3/4 in. | Up to 36 in. | 4-1/2 in. | Standard or heavy by traffic |
| 1-3/4 in. | Over 36 in. to 48 in. | 5 in. | Heavy |
| 1-3/4 in. | Over 48 in. | 6 in. | Heavy |
| 2 in. to 2-1/4 in. | Up to 42 in. | 5 in. | Heavy |
| 2 in. to 2-1/4 in. | Over 42 in. | 6 in. | Heavy |
Width is the second number and it is set by clearance, not by load. A wider leaf moves the pin farther off the frame face, which lets the door clear a deep casing, a reveal or protruding trim and swing past 90 degrees. On a flush 1-3/4 in. hollow metal opening with no trim projection, 4-1/2 x 4-1/2 is the common default; 4-1/2 x 4 shows up on many wood frames and existing openings. Both share a 4-1/2 in. height, but the full mortise leaf width differs, so match what the frame was cut for.
The typical interior office or corridor door (1-3/4 in. x 36 in. x 84 in.) takes three 4-1/2 x 4-1/2 full mortise hinges from the commercial hinges category.
How many hinges does a commercial door need?
Hinge count follows door height. The top hinge does most of the work resisting the pull of the leaf away from the frame, and the added hinges spread that load and keep the leaf flat.
| Door height | Hinges per leaf | Typical example |
|---|---|---|
| Up to 60 in. | 2 | Cabinet-height or access doors |
| Over 60 in. to 90 in. | 3 | 7 ft (84 in.) standard openings |
| Over 90 in. to 120 in. | 4 | 8 ft (96 in.) lobby and corridor doors |
| Each added 30 in. | Add 1 | Oversize openings |
Two practical exceptions. Heavy or wide leaves, doors with a heavy-duty closer and doors on high-abuse openings often get an extra hinge even when height alone would not call for it. And where the door is too heavy or abused for butts entirely, a continuous hinge is the better answer; that sizing is covered in our guide to continuous geared hinges.
For an 84 in. door, order hinges in threes; for a 96 in. door, order four per leaf from the five knuckle ball bearing hinges range.
Standard weight or heavy weight, ball bearing or plain bearing?
Weight in a hinge name means leaf thickness. The live listings show the split clearly: standard weight 4-1/2 x 4-1/2 models such as the Ives 5BB1, Hager BB1279 and McKinney TA2314 are 0.134 in. gauge, while heavy weight models such as the Ives 5BB1HW, Hager BB1199 and McKinney T4A3786 are 0.180 in. gauge.
Ives draws the line in numbers. The Ives 5BB1 standard weight hinge is recommended for medium weight doors under 150 lbs and medium frequency under 400 cycles per day, with two ball bearing assemblies, at about $12 at NLS. The Ives 5BB1HW heavy weight hinge is recommended for doors over 150 lbs and high frequency use, with four ball bearing assemblies. Both carry ANSI/BHMA A156.1 certification and a UL 10C (3 hour) listing per the product descriptions.
Bearing type is the second decision. A plain bearing hinge has no bearing between knuckles; McKinney positions its T2714 4-1/2 x 4 plain bearing hinge for low frequency doors. A closer adds constant load on every cycle, and both Ives listings state their ball bearing hinges are recommended for use with a door closer. The Stanley FBB168 listing goes further: its anti-friction bearings are described as a requirement for fire-rated and self-closing doors.
Rule for ordering: any door with a closer gets ball bearing hinges; any door over about 150 lbs or in a school, hospital or transit corridor gets heavy weight ball bearing.
Which brands make the same 4-1/2 x 4-1/2 hinge?
The 4-1/2 x 4-1/2 five knuckle full mortise hinge is made by every major hinge brand, and the standard weight and heavy weight versions line up by gauge and bearing count. The cross-reference below uses only what each live listing states. For a brand-by-brand verdict on build and value, read our Hager vs McKinney vs Stanley vs Bommer comparison.
| Brand | Standard weight model | Heavy weight model | Bearing (per listing) | Order |
|---|---|---|---|---|
| Ives | 5BB1 4.5X4.5 | 5BB1HW 4.5X4.5 | 2 ball bearings / 4 ball bearings | 5BB1HW heavy weight |
| Stanley | FBB179 4.5X4.5 (steel), FBB191 (brass, bronze or stainless) | FBB168 4.5X4.5 (steel), FBB199 (brass, bronze or stainless) | 2 ball bearings / anti-friction bearings | FBB168 heavy weight |
| Hager | BB1279 (steel), BB1191 (brass or stainless) | BB1168 (steel), BB1199 (brass or stainless) | 2 ball bearings / 4 ball bearings | BB1279 standard weight |
| McKinney | TA2314 4-1/2X4-1/2 | T4A3786 4-1/2X4-1/2 | Not stated on the base listings | Commercial hinges |
Material matters as much as brand. Hager states that the stainless steel versions of BB1191 and BB1199 comply with NFPA 80 for fire rated assemblies, and stainless or brass is the call for exterior, washdown and coastal openings. The steel FBB168 runs about $28 at NLS against about $75 for the stainless BB1199, so material, not brand, drives most of the price spread.
Pick the column (standard or heavy), pick the material, then order the matching model; all four brands sit in the commercial hinges category.
Is the door sagging from hinge wear or from the wrong hinge?
Diagnose before ordering, because a new hinge of the same wrong type will sag again. Open the door to 90 degrees, lift the latch edge and watch the knuckles.
- Vertical play at the knuckles, worn or flattened knuckle faces: worn bearing surfaces. Common on plain bearing hinges under a closer. Replace with ball bearing of the same size.
- Gap at the head on the latch side, top hinge leaf lifting off the frame: the top hinge screws are pulling out of the jamb or door. Re-anchor before replacing; a new hinge on stripped holes fails in weeks.
- Leaf bent or knuckles out of line: door weight exceeds the leaf. Move from 0.134 to 0.180 gauge heavy weight.
- Only two hinges on a 7 ft door: count problem. Add the third hinge.
- Hinges tight, door still drops: check the frame and the door itself before blaming the hardware.
Where the door is fully mortised and you are deciding whether a surface or half-surface hinge would solve a damaged frame or edge, see mortise vs non-mortise hinges before you change hinge type.
If knuckles show play on a closer door, order heavy weight ball bearing replacements in the existing size, such as the Stanley FBB168, as a full set for the leaf.
What do NRP, 26D and ETW mean in a hinge part number?
A complete hinge call reads model, size, finish and options, in roughly that order. Read each field off the existing hinge or the hardware schedule.
- Size: height x width, written 4.5X4.5, 4-1/2X4-1/2 or 5X4.5 depending on brand. The Stanley FBB191 and FBB199 both come in 5 x 4-1/2 for the wider and heavier leaves.
- Finish: US26D is satin chrome, US32D is satin stainless, US10B is oil rubbed bronze. Ives lists BHMA numbers instead (652 for satin chrome on steel, 630 for satin stainless). The full cross-reference is in our BHMA finish codes guide.
- NRP: non-removable pin. Specify it on any out-swinging door where the knuckles face the unsecured side, so the pin cannot be driven out. Hager notes the BB1168 is available with removable or non-removable pin.
- Electrified suffix: Hager uses ETW4 and ETW8 for 4 and 8 wire power transfer; McKinney uses QC12 for a 12-wire ElectroLynx connector on the T4A3786. Hager states its electric hinges are for low voltage power transfer only, 48 volts or under. The Hager BB1279 ETW4 runs about $246 at NLS, so confirm wire count against the lock and any monitoring before ordering.
On electrified openings, the hinge often carries both the lock power and the door status wiring. If you are also adding monitoring, our sibling piece on door position switches covers what to pair with it. Electrical work on these openings belongs to a qualified technician, and the AHJ governs fire-rated and egress assemblies.
Write the call as model + size + finish + options (example: BB1279 4-1/2X4-1/2 US26D NRP) and order it from the matching product page.
Common mistakes
- Ordering 4-1/2 x 4 to replace 4-1/2 x 4-1/2 because the height matches. The leaf width differs and the mortise was cut for one of them.
- Putting plain bearing hinges on a door with a closer. The bearing surfaces wear and the door drops.
- Using standard weight hinges on doors over about 150 lbs or high-traffic openings. The listings put the line at 150 lbs and 400 cycles per day.
- Hanging a 7 ft door on two hinges. Doors over 60 in. tall need three.
- Replacing hinges on stripped screw holes without re-anchoring. The new hinge sags just like the old one.
- Skipping NRP on out-swinging exterior doors where the pins face outside.
- Ordering an electrified hinge by size alone. Wire count and connector must match the lock and monitoring.
FAQ
What does 4.5 x 4.5 mean on a hinge? It means 4-1/2 in. high by 4-1/2 in. wide when the hinge is open flat. Height is always first. It is the most common size on 1-3/4 in. commercial doors up to 36 in. wide.
Is 4.5x4 the same as 4.5x4.5? No. Both are 4-1/2 in. high, but a 4-1/2 x 4 is 1/2 in. narrower when open. Match the width to the existing mortise and the clearance the door needs to swing past the casing.
What is the standard commercial door hinge size? For a 1-3/4 in. thick door up to 36 in. wide, the standard is 4-1/2 x 4-1/2 in., three per leaf on an 84 in. door. Wider or heavier doors move to 5 in. height and heavy weight.
Why is my commercial door sagging? The usual causes are worn plain bearing hinges under a closer, top hinge screws pulling out, standard weight hinges on a heavy leaf, or a missing third hinge. Check knuckle play and screw hold before ordering replacements.
Next step
Measure height and open width on the existing hinge, note the finish and whether the door has a closer or power transfer, then order from the commercial hinges category. Common picks: the Ives 5BB1 for standard doors, the Stanley FBB168 for heavy traffic, and the Hager BB1279 as a standard weight steel alternative. For a full hardware schedule, send it to the quote desk; public agencies can use government PO intake. Orders placed by 3 p.m. ET ship the same day, and orders of $450 and up ship free by ground.
SAME DAY & EXPEDITED SHIPPING AVAILABLE