Norton CPS8301 Multi-Sized Architectural Non Hold Open Door Closer, w/ CloserPlus Spring Parallel Arm

Norton CPS8301 Multi-Sized Architectural Non Hold Open Door Closer, w/ CloserPlus Spring Parallel Arm

CloserPlus® Arm
Similar to the Parallel Rigid arm, this arm incorporates a stop at the arm’s soffit plate to dead stop the door
at a predetermined degree of door swing between 85° to 110°, in 5° increments. Prior to dead stop the door
closer’s backcheck feature slows the door speed to reduce the impact of the stop action.

The CloserPlus Arm is intended for use where an auxiliary door stop cannot be utilized and no more than moderate abuse is anticipated. Where more extreme conditions are expected, use of a Unitrol arm is recommended.

CloserPlus Spring™
This arm has all the characteristics of the CloserPlus arm with an additional steel buffer spring that provides greater
protection at the end of the door opening cycle.

For extreme conditions, use of a Unitrol arm is recommended. Available with or without hold open.

FEATURES
• Exceeds 25 million cycles
• Adjustable spring sizes 1 through 6
• Non-handed
• Staked valves
• Cast aluminum closer body
• Rack and pinion design
• 1-1/4" (32mm) diameter piston
• 5/8" (16mm) diameter pinion journals
• 2-1/8" (54mm) projection (standard covers)
• All standard arm applications (with slim, full or metal covers) allow doors to swing 180 degrees, conditions permitting
• Full size template

EXPLANATION OF FEATURES

Aluminum Alloy Housing
Closer bodies are constructed of a special aluminum alloy, carefully selected to accommodate interactive steel components and operating conditions.

Rack & Pinion Operation
Provides a smooth constant control of the door through its full opening and closing cycle. 180° door swing can be
achieved when door, frame, hardware and arm function do not interfere.

Non-handed
With few exceptions all series 8301/ 8501 door closers are non-handed and can be installed on either right- or left-hand swing doors. Pinion shaft extends vertically through the closer body in both directions. Some options
will require that the hand of the closer be specified.

Non-Hold Open
Self-closes door every time door is opened. Auxiliary stop (by others)
required except when using the CloserPlus®, CloserPlus Spring™ or Unitrol® arms

Sweep Speed Control Valve
Allows adjustment of door speed from the door's full open position down to approximately 10° from the closed position.

Latch Speed Control Value
Allows adjustment of door speed from approximately 10° down to the door’s fully closed position.

Adjustable Backcheck Cushion Valve
Provides control of the door in the opening cycle, beginning at approximately 75° of door opening. It cushions the door opening when the door is forcibly opened beyond its pre-adjusted limits.

Standard Molded Covers
Molded of high-impact U.L. listed material. These covers are nonhanded for all applications.

Warranty
Limited 30-year warranty for defects and life of the building on the aluminum housing.

Closer Fluid
NorGlide® closer fluid is a specially formulated multi-viscosity hydraulic
fluid that contains lubricity and anti-oxidation agents that provide
optimum performance and efficiency.

This fluid complements the interaction of the door closer's aluminum housing
with its steel and brass components, while maintaining stable viscosity to allow the door closer to perform in
temperatures ranging from extremely high to as low as -40° F.

DOOR CLOSER POWER OPTIONS

Series 8301/8501 Multi-Sized Door Closer

Adjustable through the power range of sizes 1 through 6; as outlined in ANSI/ BHMA specification A156.4 option PT 4H.

Closers will also comply with the opening force requirements as outlined in the Americans with
Disabilities Act (ADA) and ANSI/BHMA standard A117.1 for interior doors.

CERTIFICATIONS

• ANSI/BHMA A156.4, Grade 1 certified
• UL / cUL listed for use on fire rated doors
• UL10C listed for positive pressure fire test
• 8301 and 8501 door closers are designed to comply with requirements for the Americans
  with Disabilities Act (A.D.A)and ANSI standard A117.1
• This product is manufactured in an ISO 9001, ISO 14001 facility
• UL certified environmental product declaration

CAUTION: Door Closers for Low Opening Force Applications:
Door closers installed in openings required to meet the requirements of the Americans With
Disabilities Act or ANSI/BHMA Standard A117.1, when adjusted to meet those requirements,
may not provide adequate closing power to dependably close and latch the door based on
opening or site conditions.

Model: Norton CPS8301 689, CPS8301 690, CPS8301 691, CPS8301 693, CPS8301 694